Engine Mounting Plates 500 Singles
-
- Member
- Posts: 66
- Joined: Mon May 22, 2023 1:00 am
- Location: Kent UK
Re: Engine Mounting Plates 500 Singles
Chris,
I did send you a PM, but it seems oddly stuck in my OutBox, I'm not sure if it's gone or not. Let me know if you don't get it.
Richard
I did send you a PM, but it seems oddly stuck in my OutBox, I'm not sure if it's gone or not. Let me know if you don't get it.
Richard
-
Richard
For every idiot-proof solution there is an idiot greater than the proof
Richard
For every idiot-proof solution there is an idiot greater than the proof
- spookefoote1956
- Member
- Posts: 1839
- Joined: Mon May 01, 2017 7:32 pm
- Location: Wales Innit
Re: Engine Mounting Plates 500 Singles
Got it Richard
Hail Joe Lucas ............ Prince of Darkness!
All my bikes are original........ to me!
"Creativity is your intelligence having fun" Albert Einstein
All my bikes are original........ to me!
"Creativity is your intelligence having fun" Albert Einstein
- spookefoote1956
- Member
- Posts: 1839
- Joined: Mon May 01, 2017 7:32 pm
- Location: Wales Innit
Re: Engine Mounting Plates 500 Singles
Huge thanks to Richard for his assistance. This where I'm at. This a mid 50's plate
You do not have the required permissions to view the files attached to this post.
Last edited by spookefoote1956 on Tue Jun 27, 2023 3:06 pm, edited 1 time in total.
Hail Joe Lucas ............ Prince of Darkness!
All my bikes are original........ to me!
"Creativity is your intelligence having fun" Albert Einstein
All my bikes are original........ to me!
"Creativity is your intelligence having fun" Albert Einstein
- spookefoote1956
- Member
- Posts: 1839
- Joined: Mon May 01, 2017 7:32 pm
- Location: Wales Innit
Re: Engine Mounting Plates 500 Singles
Morning again Richard. My frame is the Girling one and should be right for you. I'll get onto itRichardS wrote: ↑Mon Jun 26, 2023 2:49 pm I have a similar requirement for a slightly different reason and I'd be happy to collaborate - I do plenty of CAD and was intending to get some alloy plates water-jet cut once I can get the dimensions accurate - I have no correct plates at present. I have plates for a rigid single with a CP box and for a twin I thought in a duplex frame, but it doesn't match a AMC box which is odd.
A quick and reasonably effective way to CAD-ify them is to take a decently high resolution photo (modern phone is easily good enough) straight/square on and then vectorise that, but a tracing works fine too of course.
My actual requirement is that I have a twin tube Comp frame, a long stroke comp. motor and an AMC gearbox. It shouldn't be too hard to match them up, but without knowing the shape I'm looking for when trawling fleaBay or autojumbes the part numbers in the Parts Manual don't really help.
Chris, do you have CAD for the plate in your photo? Looks to be just what I'm after
Richard
Hail Joe Lucas ............ Prince of Darkness!
All my bikes are original........ to me!
"Creativity is your intelligence having fun" Albert Einstein
All my bikes are original........ to me!
"Creativity is your intelligence having fun" Albert Einstein
- spookefoote1956
- Member
- Posts: 1839
- Joined: Mon May 01, 2017 7:32 pm
- Location: Wales Innit
Re: Engine Mounting Plates 500 Singles
If anyone's got a Girling frame one knocking about then let me know please. The anchorage to the frame at the rear is different
Hail Joe Lucas ............ Prince of Darkness!
All my bikes are original........ to me!
"Creativity is your intelligence having fun" Albert Einstein
All my bikes are original........ to me!
"Creativity is your intelligence having fun" Albert Einstein
- dave16mct
- Member
- Posts: 3246
- Joined: Mon Jan 01, 1990 12:00 am
- Location: LANCASHIRE UK
Re: Engine Mounting Plates 500 Singles
Hi Chris,
what's the 5/8" hole for? My plate doesn't have that.
Dave.
what's the 5/8" hole for? My plate doesn't have that.
Dave.
- spookefoote1956
- Member
- Posts: 1839
- Joined: Mon May 01, 2017 7:32 pm
- Location: Wales Innit
Re: Engine Mounting Plates 500 Singles
That is a good question Dave. I took it from Richard's dxf. Easy to remove.
Hail Joe Lucas ............ Prince of Darkness!
All my bikes are original........ to me!
"Creativity is your intelligence having fun" Albert Einstein
All my bikes are original........ to me!
"Creativity is your intelligence having fun" Albert Einstein
- Joker_Bones
- Member
- Posts: 545
- Joined: Sat Apr 27, 2013 3:51 pm
- Location: DORSET UK
Re: Engine Mounting Plates 500 Singles
These are plates for a duplex frame single.
I have the original plate I used to cut these out.
Happy to trace round it if that is what is needed?
You do not have the required permissions to view the files attached to this post.
- spookefoote1956
- Member
- Posts: 1839
- Joined: Mon May 01, 2017 7:32 pm
- Location: Wales Innit
Re: Engine Mounting Plates 500 Singles
Oh yes please!
Hail Joe Lucas ............ Prince of Darkness!
All my bikes are original........ to me!
"Creativity is your intelligence having fun" Albert Einstein
All my bikes are original........ to me!
"Creativity is your intelligence having fun" Albert Einstein
- spookefoote1956
- Member
- Posts: 1839
- Joined: Mon May 01, 2017 7:32 pm
- Location: Wales Innit
Re: Engine Mounting Plates 500 Singles
OK groovy cats here's the updated ones without the extra hole
You do not have the required permissions to view the files attached to this post.
Hail Joe Lucas ............ Prince of Darkness!
All my bikes are original........ to me!
"Creativity is your intelligence having fun" Albert Einstein
All my bikes are original........ to me!
"Creativity is your intelligence having fun" Albert Einstein