G12 CSR Front Mudguard Stay Bracket
-
- Posts: 3
- Joined: Mon Jan 02, 2023 5:08 pm
- Location: Cambridgeshire
G12 CSR Front Mudguard Stay Bracket
Would anyone be able to tell me the dimensions of the front mudguard stay bracket (the plate between the stay and the mudguard) and the diameter of the stay please?
thanks Nick
thanks Nick
-
- Member
- Posts: 39
- Joined: Sat Jan 15, 2022 5:51 pm
- Location: Bedfordshire UK
Re: G12 CSR Front Mudguard Stay Bracket
Do you mean the 'U' shaped bracket that goes over the mudguard or the plate that goes underneath it?
-
- Posts: 3
- Joined: Mon Jan 02, 2023 5:08 pm
- Location: Cambridgeshire
Re: G12 CSR Front Mudguard Stay Bracket
No the small bracket about 2" long with two holes, two on each stay loop, if that makes sense? I can't see how to add a photo.
Thanks
Thanks
Last edited by Duzmo on Mon Jan 09, 2023 11:26 am, edited 1 time in total.
- robcurrie
- Member
- Posts: 956
- Joined: Fri Dec 09, 2011 5:33 pm
- Location: Limpopo SOUTH AFRICA
- Contact:
Re: G12 CSR Front Mudguard Stay Bracket
Nick,
I have attached a picture of the front end of my AJS 31 CSR, your G12 should be identical. The bracket fits inside the ally mudguard. Which dimensions do you need or do you need to manufacture a new bracket?
Rob C
I have attached a picture of the front end of my AJS 31 CSR, your G12 should be identical. The bracket fits inside the ally mudguard. Which dimensions do you need or do you need to manufacture a new bracket?
Rob C
You do not have the required permissions to view the files attached to this post.
- clive
- Member
- Posts: 5671
- Joined: Mon Jan 01, 1990 12:00 am
- Location: LONDON UK
Re: G12 CSR Front Mudguard Stay Bracket
Duzmo as a guest you can only post a picture in a hosting site and post a link. I think the brackets you are talking about are the two on the stays which allow them to be bolted to the mudguard rather than the bracket between two fork legs. I would measure mine but they are sure to be repro items and in any case are different between my bikes, looking at the photo posted above you could make an estimate as to what length looks right.
clive
if it ain't broke don't fix
if it ain't broke don't fix
-
- Member
- Posts: 39
- Joined: Sat Jan 15, 2022 5:51 pm
- Location: Bedfordshire UK
Re: G12 CSR Front Mudguard Stay Bracket
You mean the four brackets, 2 front, 2 rear that are welded to the front and rear mudguard stays? I will have a measure for you.
-
- Member
- Posts: 39
- Joined: Sat Jan 15, 2022 5:51 pm
- Location: Bedfordshire UK
Re: G12 CSR Front Mudguard Stay Bracket
My 'U' shaped bracket goes over the mudguard and there is a smaller washer plate that sits beneath it.
-
- Member
- Posts: 39
- Joined: Sat Jan 15, 2022 5:51 pm
- Location: Bedfordshire UK
Re: G12 CSR Front Mudguard Stay Bracket
Hi Nick,
The mudguards stays are 7/16" dia tubing.
The small brackets welded to these stays are 2" long x 5/8" wide. there are two clearance holes for 2BA bolts and these are on 1 3/8" centres. Note that the ends are not full rads. My radius gauges don't go large enough to tell you what the actual radius is however.
Hoe this helps, John.
p.s. I think my mudguard stays are original so I'm fairly certain I've given you accurate information.
- ajscomboman
- Member
- Posts: 3960
- Joined: Mon Jan 01, 1990 12:00 am
- Location: HAMPSHIRE UK
Re: G12 CSR Front Mudguard Stay Bracket
That is the correct set up, my old but worn out original with the riveted steel plates had the main bracket over the outside and a smaller shaped strengthening plate on the under side.Columbo John wrote: ↑Wed Jan 11, 2023 7:21 amMy 'U' shaped bracket goes over the mudguard and there is a smaller washer plate that sits beneath it.
Best get busy swapping yours over Rob.
-
- Member
- Posts: 3534
- Joined: Sun Jan 01, 1995 12:00 am
- Location: ESSEX UK
Re: G12 CSR Front Mudguard Stay Bracket
Your forks look wrong with square bottom caps and early top nuts.
Roy