Hi all I’m afraid there is going to be loads of questions on this project, but to start with valve springs….
The springs are very worn and all different lengths so don’t know what they should be but would they have only been made for the one or two years the 250 was made or would they be the same as other machines? Possibly later ones as I’ve tried the old part numbers to new but can’t find anything. The numbers are
Outer spring
serial number 191
Interchangeability ZB2240
Drawing number 16928
Inner spring
Serial number 192
Interchangeability ZB2260
Drawing number 16929
I’m also presuming that the top valve seat that holds the collets is called a “valve spring cone” and the bottom is called “valve spring dish” because the drawing is a bit confusing.
Thanks
1933 250 big port valve springs
-
- Member
- Posts: 388
- Joined: Tue May 25, 2021 10:50 pm
- Location: Oxfordshire UK
1933 250 big port valve springs
You do not have the required permissions to view the files attached to this post.
Everyday’s a learning curve.
- Duncan
- Member
- Posts: 2141
- Joined: Thu Jul 10, 2003 1:00 am
- Location: HAMPSHIRE UK
Re: 1933 250 big port valve springs
Hi Neil
I assume that you are already familiar with the archive, doe this help with spring sizes? http://archives.jampot.dk/technical/Pis ... 0_1960.pdf
It may help if you refer to the bike by the model number as the big port name encompasses several models over the years.
I assume that you are already familiar with the archive, doe this help with spring sizes? http://archives.jampot.dk/technical/Pis ... 0_1960.pdf
It may help if you refer to the bike by the model number as the big port name encompasses several models over the years.
- Rob Harknett
- Member
- Posts: 11211
- Joined: Mon Jan 01, 1990 12:00 am
- Location: ESSEX UK
Re: 1933 250 big port valve springs
1933 model 12 250 OHV "Big Port " all the Wolverhampton AJS got referred as an AJS Big Port. I guess AJS thought , you want it named as a big port OK.Duncan wrote: ↑Wed Mar 30, 2022 3:41 pm Hi Neil
I assume that you are already familiar with the archive, doe this help with spring sizes? http://archives.jampot.dk/technical/Pis ... 0_1960.pdf
It may help if you refer to the bike by the model number as the big port name encompasses several models over the years.
So in the 1933 sales cat. they added big port in brackets into the model info. There's no info in the archives files for valve springs for 1933 model 12.
-
- Member
- Posts: 388
- Joined: Tue May 25, 2021 10:50 pm
- Location: Oxfordshire UK
Re: 1933 250 big port valve springs
Thanks guys, I’ve found a set of valve springs on ebay that the measurements seem to be the same so have ordered them, there from France and the guy says they fit a WD so hoping they fit
Everyday’s a learning curve.
- Duncan
- Member
- Posts: 2141
- Joined: Thu Jul 10, 2003 1:00 am
- Location: HAMPSHIRE UK
Re: 1933 250 big port valve springs
That sounds like Terrys VS82, they were common for OHV 250cc, 350cc and 500cc from the late 1930's up to 1947, I picked a nos set up at Kempton autojumble least year but was not sure how they related to earlier engines.
-
- Member
- Posts: 388
- Joined: Tue May 25, 2021 10:50 pm
- Location: Oxfordshire UK
Re: 1933 250 big port valve springs
Cheers that’s sort of the conclusion I came to so I hope I’m right, they were not listed as vs82 just had measurements which all seemed close apart from the length but expect mine are well worn though his measurement of the small spring was about 4 mm longer than listed on the Terry’s list.
Neil
Neil
Everyday’s a learning curve.