Wet sumping while running

Information relating to the Matchless G80 or AJS Model 18 500cc Heavyweight.
Member
User avatar
Posts: 248
Joined: Sat Dec 17, 2016 5:26 pm
Location: Taunton somerset

Re: Wet sumping while running

Postby Harry44 » Wed Jun 17, 2020 7:33 am

At least I'm not the only one to suffer wet sumping with the engine running. Hope you get yours fixed


Harry
si is does non opportunus vos postulo a maior pango

Member
Posts: 6745
Joined: Wed Sep 01, 2004 12:00 am
Location: WEST SUSSEX UK

Re: Wet sumping while running

Postby SPRIDDLER » Wed Jun 17, 2020 7:46 am

56G80S wrote:Sprid

Thanks. Mine will pass through the bush. Cheeky but where is the data on wear limits?


Where relevant I use the Army Inspection Standards for my '54 model. Good move to check the wear limits as I've no idea why, (probably senility) I gave you the wrong dims for bush wear :oops: although your bush seems to be right on the acceptable limit.

http://archives.jampot.dk/book/Workshop ... ndards.pdf

See page 8........

Bush timing side dims (640x321).jpg
You do not have the required permissions to view the files attached to this post.
I poke badgers with spoons.

Member
Posts: 2484
Joined: Wed Oct 12, 2005 9:45 pm
Location: N YORKS UK

Re: Wet sumping while running

Postby 56G80S » Wed Jun 17, 2020 4:02 pm

Thanks Sprid

It took me a while to work out but I realise that 6 thou looks like the condemn point. I was only guessing at the play. Short of a dial gauge on the end of the axle..............

I reckon the play is too great and it's stuffed one way or another but perhaps not so much that the pump plunger will be as well (hopes).

I'll pick this up again when I get the cases split.

Cheers

Johnny B

Member
Posts: 2484
Joined: Wed Oct 12, 2005 9:45 pm
Location: N YORKS UK

Re: Wet sumping while running

Postby 56G80S » Thu Jun 18, 2020 12:02 pm

Rocker box and head off now. What a lot of carbon. It had obviously been running too rich but at least it's not oily. I probably left it rich for the running in after barrel re-sleeve and didn't weaken it later. Somewhat oddly, both pushrods were very, very slack. Maybe I did this when I was carrying out explorations at the Jampot. I really hope so.

Put some 3-in-1 oil in the top threads of the barrel nuts and maybe I won't wind the studs out like last time I took the barrel off. MIght pop some Plus gas in too. They tend to get water sitting in them.

Johnny B

Member
Posts: 2484
Joined: Wed Oct 12, 2005 9:45 pm
Location: N YORKS UK

Re: Wet sumping while running

Postby 56G80S » Thu Jun 18, 2020 5:51 pm

Me again

Well, the nuts came off nicely. Unfortunately, the barrel is naughty word, naughty word. the inlet side of the piston is also naughty word. The former is cored sufficiently that I can feel it through the "rubber" gloves. I wonder it T&L can remove the liner and do it again? The piston has at least one piece of brass and probably more tightly ensconced in the line with the inlet valve.

Ironically I had made a nice job of reaming the small end and fitting the piston.

Lost heart at this point and will proceed to removal of the engine tomorrow or over the week-end.

So the target now is Easter next year.

Johnny B

Member
User avatar
Posts: 248
Joined: Sat Dec 17, 2016 5:26 pm
Location: Taunton somerset

Re: Wet sumping while running

Postby Harry44 » Sun Jun 21, 2020 6:52 pm

Heart breaking I feel for you mate

Cheers Harry
si is does non opportunus vos postulo a maior pango

Previous

Return to G80 / Model 18

Who is online

Users browsing this forum: No registered users and 15 guests