Fork sliders
-
- Member
- Posts: 452
- Joined: Tue May 27, 2003 1:00 am
- Location: SHROPSHIRE UK
Re: Fork sliders
Like mick D posted to make sure the shoulder is slightly below or just flush. I hope it works out fine.
-
- Posts: 5
- Joined: Tue Apr 22, 2014 9:44 am
- Location: Madrid, Spain
Re: Fork sliders
I also have problems with my replacement front forks. I believe they are from a 1956 AJS (my bike is a 1946 G3L conveted to G8L) but I dont know if they are 1 1/8 or 1 1/4 How can I tell? I would like to buy the club stainless steel fork slider extensions. Secondly, the lug on the bottom aluminium slider on the RHS has broken off. Can I get a replacement (new or s/hand) or should I try to get it allly welded? Thirdly,is it essential to have the special tool to pull the fork tube up into the yoke? I note the club tool is £73!
-
- Posts: 2886
- Joined: Mon Mar 24, 2014 5:44 pm
- Location: Aberdeenshire
Re: Fork sliders
Hi
The dimension is the diameter of the stanchion.
Replacement 1 - 1/4" sliders are available but at a price - AMC Classic Spares may be able to help with a second hand one - welding is a difficult option and may not be successful.
Yes, the fork tool is required but there are much cheaper options available, check club spares and AMC Classic
Regards Mick
The dimension is the diameter of the stanchion.
Replacement 1 - 1/4" sliders are available but at a price - AMC Classic Spares may be able to help with a second hand one - welding is a difficult option and may not be successful.
Yes, the fork tool is required but there are much cheaper options available, check club spares and AMC Classic
Regards Mick
- ajscomboman
- Member
- Posts: 3971
- Joined: Mon Jan 01, 1990 12:00 am
- Location: HAMPSHIRE UK
Re: Fork sliders
No, that's the dismantling tool not the pulling tool, but we're out of stock of the puller.arthurmatchless wrote:I also have problems with my replacement front forks. I believe they are from a 1956 AJS (my bike is a 1946 G3L conveted to G8L) but I dont know if they are 1 1/8 or 1 1/4 How can I tell? I would like to buy the club stainless steel fork slider extensions. Secondly, the lug on the bottom aluminium slider on the RHS has broken off. Can I get a replacement (new or s/hand) or should I try to get it allly welded? Thirdly,is it essential to have the special tool to pull the fork tube up into the yoke? I note the club tool is £73!
- Pharisee
- Member
- Posts: 1127
- Joined: Tue Mar 15, 2016 8:51 pm
- Location: Lincolnshire UK
- Contact:
Re: Fork sliders
Just had a look at the above mentioned fork dismantling tool on the AMOC Spares website. The picture only seems to show a part of it. How is it used, please?ajscomboman wrote:No, that's the dismantling tool not the pulling tool, but we're out of stock of the puller.arthurmatchless wrote:I also have problems with my replacement front forks. I believe they are from a 1956 AJS (my bike is a 1946 G3L conveted to G8L) but I dont know if they are 1 1/8 or 1 1/4 How can I tell? I would like to buy the club stainless steel fork slider extensions. Secondly, the lug on the bottom aluminium slider on the RHS has broken off. Can I get a replacement (new or s/hand) or should I try to get it allly welded? Thirdly,is it essential to have the special tool to pull the fork tube up into the yoke? I note the club tool is £73!
I'm from the Fens.... Gimme six.
-
- Member
- Posts: 352
- Joined: Tue Jul 28, 2009 5:51 pm
- Location: BERKSHIRE UK
Re: Fork sliders
You attach one end (the one not shown) using a fork puller, and the bit shown in the pictures "takes place" of your wheel spindle. You then just slowly do the nut at the far end up which "cranks" the slider out like a hot knife through butter. (Works a treat)
-
- Posts: 2886
- Joined: Mon Mar 24, 2014 5:44 pm
- Location: Aberdeenshire
Re: Fork sliders
Hi
So effectively it's just for removing the oil seals, yes?
Didn't know this tool existed - when I dis-assembled my forks I found no need for it, perhaps I was just lucky.
Rather expensive if the price doesn't include the puller.
Regards Mick
So effectively it's just for removing the oil seals, yes?
Didn't know this tool existed - when I dis-assembled my forks I found no need for it, perhaps I was just lucky.
Rather expensive if the price doesn't include the puller.
Regards Mick
- Pharisee
- Member
- Posts: 1127
- Joined: Tue Mar 15, 2016 8:51 pm
- Location: Lincolnshire UK
- Contact:
Re: Fork sliders
Ok... so it just literally pulls the forks apart... for seventy three of our fine Great British Pounds. Hmmm
I push them apart with a steel disc I bought off eBay, a length of 3/8" studding and a couple of Allen screws... Cost... less than a tenner.
I'm sure someone will come along and tell me how and why I'm doing it all wrong but it works for me!!
I push them apart with a steel disc I bought off eBay, a length of 3/8" studding and a couple of Allen screws... Cost... less than a tenner.
I'm sure someone will come along and tell me how and why I'm doing it all wrong but it works for me!!
You do not have the required permissions to view the files attached to this post.
I'm from the Fens.... Gimme six.
-
- Posts: 2886
- Joined: Mon Mar 24, 2014 5:44 pm
- Location: Aberdeenshire
Re: Fork sliders
Hi
Nowt wrong with John's, (Pharisee), solution, if the seals are 'difficult' it's the method I'd use.
Draining the forks, (leave the drain screws out), gripping the slider in a vice and yanking the stanchion from full compression to full extension a few times had my seals out in seconds.
Regards Mick
Nowt wrong with John's, (Pharisee), solution, if the seals are 'difficult' it's the method I'd use.
Draining the forks, (leave the drain screws out), gripping the slider in a vice and yanking the stanchion from full compression to full extension a few times had my seals out in seconds.
Regards Mick
-
- Posts: 160
- Joined: Tue Apr 25, 2017 1:24 pm
- Location: York
Re: Fork sliders
My forks were crazy hard to get apart and stupidly I had forgotten about Pharisee's solution which I had read about a while before so I made my own up. Pharisee's solution is much simpler than mine and just as effective. Here is mine.Pharisee wrote:Ok... so it just literally pulls the forks apart... for seventy three of our fine Great British Pounds. Hmmm
I push them apart with a steel disc I bought off eBay, a length of 3/8" studding and a couple of Allen screws... Cost... less than a tenner.
I'm sure someone will come along and tell me how and why I'm doing it all wrong but it works for me!!
John