Kickstart
32 posts
• Page 2 of 4 • 1, 2, 3, 4
Re: Kickstart
following the same dimensions as Clanger9's mine 200mm with an off set of approx 40mm and fitted to a 1967 250CSR
Re: Kickstart
Wow, so *at least* three different ones then... 

1989 Moto Morini Dart 350
1993 Ducati 750SS
1993 Ducati 750SS
Re: Kickstart
Hi All
Thanks Pete for showing these
''Kickstart, may get someone out of trouble..... Hen's teeth I believe.
https://www.ebay.co.uk/itm/AJS-MODEL14- ... SwW0Vb5a4H ''
I have purchased one and they are short by about 1" to the original, also they will foul the silencer!
I intend to cut mine and weld in a section to make it the right length, then try and bend out slightly so it misses / does not foul the silencer.
I am lucky to know someone who has an original, so will try to make it look like this, obviously when I have finished I will have to get re-chromed
Gary
Thanks Pete for showing these

''Kickstart, may get someone out of trouble..... Hen's teeth I believe.
https://www.ebay.co.uk/itm/AJS-MODEL14- ... SwW0Vb5a4H ''
I have purchased one and they are short by about 1" to the original, also they will foul the silencer!
I intend to cut mine and weld in a section to make it the right length, then try and bend out slightly so it misses / does not foul the silencer.
I am lucky to know someone who has an original, so will try to make it look like this, obviously when I have finished I will have to get re-chromed
Gary
- Peter Morris
- Member
-
- Posts: 668
- Joined: Wed Mar 05, 2014 4:21 pm
- Location: Oxted, Surrey
Re: Kickstart
Woodland wrote:
I intend to cut mine and weld in a section to make it the right length, then try and bend out slightly so it misses / does not foul the silencer.
I am lucky to know someone who has an original, so will try to make it look like this, obviously when I have finished I will have to get re-chromed
Gary
I would imagine that anything is possible if you are prepared to get it welded and re-chromed........ as long as the splines fit properly. I am lucky enough to have a village blacksmith where I live, he welded 2' extra length into the kickstart of my G15 to give a bit more leverage, once it was chromed only the most observant rivet counter would notice. He also lengthened a roadster prop stand for my G3C with no problems whatsoever.
Re: Kickstart
Peter Morris wrote: I am lucky enough to have a village blacksmith where I live, he welded 2'extra length into the kickstart of my G15 to give a bit more leverage, .......
It's a hand start now then?

I poke badgers with spoons.....from 2 metres.
- Peter Morris
- Member
-
- Posts: 668
- Joined: Wed Mar 05, 2014 4:21 pm
- Location: Oxted, Surrey
Re: Kickstart
It might be for Geoff Capes Nev 😂
Re: Kickstart
Looks to me one of them would be handy to have for a 250/350? eBay item number:
153338728276
153338728276
?
- ajscomboman
- Member
-
- Posts: 3214
- Joined: Mon Jan 01, 1990 12:00 am
- Location: HAMPSHIRE UK
Re: Kickstart
Wouldn't dive in too fast. A little bird has it that the spares service may well be stocking kickstarts in the near future if discussions go well. .
32 posts
• Page 2 of 4 • 1, 2, 3, 4
Who is online
Users browsing this forum: No registered users and 5 guests