1959 G3C ('62 Shortstoke Engine) cam problems
-
- Member
- Posts: 8549
- Joined: Wed Sep 01, 2004 1:00 am
- Location: WEST SUSSEX UK
Re: 1959 G3C ('62 Shortstoke Engine) cam problems
You know Les at Russells pretty well. He has many ex factory service dep't tools.
If that fails you can always ask him to extract the Easyout with his teeth as on a bad day he has quite a bite.
If that fails you can always ask him to extract the Easyout with his teeth as on a bad day he has quite a bite.
'There is a tide in the affairs of men
Which taken at the flood............'
Which taken at the flood............'
- Peter Morris
- Member
- Posts: 733
- Joined: Wed Mar 05, 2014 4:21 pm
- Location: SURREY UK
Re: 1959 G3C ('62 Shortstoke Engine) cam problems
Thanks Pete, I will have a look for a Rawlbolt if Les cannot help with a special tool for the job.
Hopefully he may be able to identify the cam too.
When Nev mentioned the Rawlbolt earlier I was visualising a toggle bolt.... no wonder I couldn't see how it could work
![Rolling Eyes :roll:](./images/smilies/icon_rolleyes.gif)
Hopefully he may be able to identify the cam too.
When Nev mentioned the Rawlbolt earlier I was visualising a toggle bolt.... no wonder I couldn't see how it could work
![Rolling Eyes :roll:](./images/smilies/icon_rolleyes.gif)
![Rolling Eyes :roll:](./images/smilies/icon_rolleyes.gif)
-
- Member
- Posts: 8549
- Joined: Wed Sep 01, 2004 1:00 am
- Location: WEST SUSSEX UK
Re: 1959 G3C ('62 Shortstoke Engine) cam problems
Yes, the Rawlbolt I had in mind would be one of these......
Perhaps wrap some coarse emery cloth around it to add friction and avoid needing too much expansion to grip the bush.............
Not quite the same thing but I found one very effective in replacing a cheap 'n nasty internal expander bracket for a 'bar end mirror that previously had Brewer's Droop every time I hit a bump.
Perhaps wrap some coarse emery cloth around it to add friction and avoid needing too much expansion to grip the bush.............
![Question :?:](./images/smilies/icon_question.gif)
Not quite the same thing but I found one very effective in replacing a cheap 'n nasty internal expander bracket for a 'bar end mirror that previously had Brewer's Droop every time I hit a bump.
You do not have the required permissions to view the files attached to this post.
'There is a tide in the affairs of men
Which taken at the flood............'
Which taken at the flood............'
- Peter Morris
- Member
- Posts: 733
- Joined: Wed Mar 05, 2014 4:21 pm
- Location: SURREY UK
-
- Member
- Posts: 452
- Joined: Tue May 27, 2003 1:00 am
- Location: SHROPSHIRE UK
Re: 1959 G3C ('62 Shortstoke Engine) cam problems
another tip is the one used on triumph twin cam bushes, screw in a tap as if cutting a thread , heat up case extract bush and tap as one.
you can see this being done on youtube.
you can see this being done on youtube.
- Peter Morris
- Member
- Posts: 733
- Joined: Wed Mar 05, 2014 4:21 pm
- Location: SURREY UK
Re: 1959 G3C ('62 Shortstoke Engine) cam problems
Thanks Alan, that's an option.... obviously have to be careful nothing drops inside.
- Peter Morris
- Member
- Posts: 733
- Joined: Wed Mar 05, 2014 4:21 pm
- Location: SURREY UK
Re: 1959 G3C ('62 Shortstoke Engine) cam problems
UPDATE:
Finally got round to the G3C cams,
On g80csp11 Peter's recommendation I bought one of these https://www.ebay.co.uk/itm/5pc-INNER-BE ... 2749.l2649
Bit of heat, the bushes came out VERY easily without dismantling the cases........ Cheap at twice the price!!!
Finally got round to the G3C cams,
On g80csp11 Peter's recommendation I bought one of these https://www.ebay.co.uk/itm/5pc-INNER-BE ... 2749.l2649
Bit of heat, the bushes came out VERY easily without dismantling the cases........ Cheap at twice the price!!!
You do not have the required permissions to view the files attached to this post.
-
- Member
- Posts: 744
- Joined: Thu Mar 31, 2005 1:00 am
- Location: BERKS UK
Re: 1959 G3C ('62 Shortstoke Engine) cam problems
Have just seen this thread. The cam shown is almost certainly a standard roadster, I have competition cams in my 18S and they look very different, less 'pointed' at the nose. The spindles will come out easily enough in a Chinese 10 ton press as found in many car servicing garages. I swapped spindles myself, and got protruding length right. However, I would advise turning a distance piece to ensure replacement spindle goes in the right amount. Andy
- Peter Morris
- Member
- Posts: 733
- Joined: Wed Mar 05, 2014 4:21 pm
- Location: SURREY UK
Re: 1959 G3C ('62 Shortstoke Engine) cam problems
Thanks Andy, It's all back together and running very well.
I am on the lookout for some new cams but since changing the bushes it is fine.
Peter
I am on the lookout for some new cams but since changing the bushes it is fine.
Peter