m16 replacement carby
-
- Posts: 6
- Joined: Sat Feb 17, 2018 2:54 am
- Location: australia
m16 replacement carby
Hello
Have just purchased my first AJS 16m 1951 rigid. It hasnt arrived yet but the owner says its having starting /carby problems and recommends i buy a new replacement carby. Could anyone recommend a good Amal replacement carby.
Haddy
Have just purchased my first AJS 16m 1951 rigid. It hasnt arrived yet but the owner says its having starting /carby problems and recommends i buy a new replacement carby. Could anyone recommend a good Amal replacement carby.
Haddy
-
- Member
- Posts: 746
- Joined: Thu Mar 31, 2005 1:00 am
- Location: BERKS UK
Re: m16 replacement carby
Amal still make most carby models, so you should be able to get whatever the manual/parts book says. Andy
- Rob Harknett
- Member
- Posts: 11211
- Joined: Mon Jan 01, 1990 12:00 am
- Location: ESSEX UK
Re: m16 replacement carby
Wait until you get the bike. First make sure all the settings are correct. Start at timing , ignition timing, points, gap. lead & connection plug. Does not matter what carb you have unless that is all correct. Also you have not spent, perhaps wasted any money.
-
- Member
- Posts: 8561
- Joined: Wed Sep 01, 2004 1:00 am
- Location: WEST SUSSEX UK
Re: m16 replacement carby
Welcome, Haddy.
Originally it would have had an AMAL 'Pre Monobloc' at around £375. Many/most have been replaced with the AMAL 'Monobloc' at around £150. The Monobloc was the standard carb fitted from '55 right up until the end of AMC in the late 60's.
Available from this club's Spares Scheme. See: http://www.amoc-parts.com/store/comersu ... oducts.asp
As said above, first give yours a good clean - especially the tiny drillings in the body because if it has been standing unused today's fuel with ethanol will have gummed up the carb, then tune it following this guide:
http://www.hitchcocksmotorcycles.com/mo ... to-tune-up
And if you haven't done so already, join the Club and the Spares Scheme and get 10% off the cost of parts. See here: http://www.jampot.com/spares.asp
Enjoy!
Originally it would have had an AMAL 'Pre Monobloc' at around £375. Many/most have been replaced with the AMAL 'Monobloc' at around £150. The Monobloc was the standard carb fitted from '55 right up until the end of AMC in the late 60's.
Available from this club's Spares Scheme. See: http://www.amoc-parts.com/store/comersu ... oducts.asp
As said above, first give yours a good clean - especially the tiny drillings in the body because if it has been standing unused today's fuel with ethanol will have gummed up the carb, then tune it following this guide:
http://www.hitchcocksmotorcycles.com/mo ... to-tune-up
And if you haven't done so already, join the Club and the Spares Scheme and get 10% off the cost of parts. See here: http://www.jampot.com/spares.asp
Enjoy!
You do not have the required permissions to view the files attached to this post.
Last edited by SPRIDDLER on Sat Feb 17, 2018 12:18 pm, edited 2 times in total.
'There is a tide in the affairs of men
Which taken at the flood............'
Which taken at the flood............'
- kernow kid
- Posts: 517
- Joined: Wed Feb 14, 2007 3:55 pm
- Location: CORNWALL UK
Re: m16 replacement carby
Hi haddy,
Yes, join the Club!
Also refer to archives.jampot.dk for the relevant manuals for your bike. Study and inwardly digest, especially the parts manuals as these will help you work out if you've got any 'odd bits' on the bike. It's surprising what gets changed over 65 years!
Most of all enjoy your AJ and post a few pics as we are all nosey buggers, plus it's a very quick way of finding out what odd bits you've got...but most of us don't care much as long as it's another AMC bike being enjoyed.
Regards kk
Yes, join the Club!
Also refer to archives.jampot.dk for the relevant manuals for your bike. Study and inwardly digest, especially the parts manuals as these will help you work out if you've got any 'odd bits' on the bike. It's surprising what gets changed over 65 years!
Most of all enjoy your AJ and post a few pics as we are all nosey buggers, plus it's a very quick way of finding out what odd bits you've got...but most of us don't care much as long as it's another AMC bike being enjoyed.
Regards kk
Top tip - if it needs more than 2 bolts to hold it on, its probably important...
-
- Posts: 6
- Joined: Sat Feb 17, 2018 2:54 am
- Location: australia
Re: m16 replacement carby
Than for the info chaps this is my first AJS.
iam a BSA man,bantam,c11, b40(what a bomb) and an M20.
I will go over it thoroughly first. But i would still like to know if anyone is running an Amal concentric.
Haddy
iam a BSA man,bantam,c11, b40(what a bomb) and an M20.
I will go over it thoroughly first. But i would still like to know if anyone is running an Amal concentric.
Haddy
-
- Posts: 6
- Joined: Sat Feb 17, 2018 2:54 am
- Location: australia
Re: m16 replacement carby
tried to post a photo but under options there is no upload attachment.
Haddy
Haddy
- clive
- Member
- Posts: 5671
- Joined: Mon Jan 01, 1990 12:00 am
- Location: LONDON UK
Re: m16 replacement carby
We have had this before, I think as a guest member you are only able to place a picture if it its hosted elsewhere with a URL reference to it, not able to upload a picture directly on the site.
clive
if it ain't broke don't fix
if it ain't broke don't fix
- kernow kid
- Posts: 517
- Joined: Wed Feb 14, 2007 3:55 pm
- Location: CORNWALL UK
Re: m16 replacement carby
Hi haddy,
I'm running a concentric on my 1959 16ms, and with a little tuning it runs very well. It's easier to get any carb to run badly, but there is more info on what is the best set up for the original fit, monobloc.
Regards kk
I'm running a concentric on my 1959 16ms, and with a little tuning it runs very well. It's easier to get any carb to run badly, but there is more info on what is the best set up for the original fit, monobloc.
Regards kk
Top tip - if it needs more than 2 bolts to hold it on, its probably important...
-
- Member
- Posts: 746
- Joined: Thu Mar 31, 2005 1:00 am
- Location: BERKS UK
Re: m16 replacement carby
I run a concentric on my '54 18S - got it new from a fellow member at a good price who no longer needed it. It goes well and, most importantly, gives me a much better tickover than the worn out original carb. Main jet monobloc size + 20%, others the same as for monobloc. Andy