Well the engine rebuild went well. New main bearings big end bearing and small end bush glaze bust new piston and rings. Copper head gasket between head and barrel just for variety.
She starts and runs without nasty noises, or oil leaks (yet) enough compression to support my 19 stone frame I definitely need to improve my technique.
Just one snagette the new kick start return spring has popped out of the inner case
Has anyone else had this problem ?
Edith update
- Harry44
- Member
- Posts: 280
- Joined: Sat Dec 17, 2016 5:26 pm
- Location: SOMERSET UK
Edith update
si is does non opportunus vos postulo a maior pango
-
- Posts: 109
- Joined: Thu Jun 05, 2008 8:15 pm
- Location: KENT UK
Re: Edith update
Good news Harry. I hope mine goes as well when I get it back together, except for the kickstart problem of course.
If it ain't broke, fix it till it is.
- Harry44
- Member
- Posts: 280
- Joined: Sat Dec 17, 2016 5:26 pm
- Location: SOMERSET UK
Re: Edith update
Having compared the old spring with the new one, the new spring has a shorter "tang" that goes into the hole in the inner case and it also does not hook back on itself to lock into place.
With the old one back in the gearbox it stays in place but can't return the kick start without assistance.
Does anyone know if this is a common problem ? or have a solution ?
With the old one back in the gearbox it stays in place but can't return the kick start without assistance.
Does anyone know if this is a common problem ? or have a solution ?
si is does non opportunus vos postulo a maior pango
- clive
- Member
- Posts: 5670
- Joined: Mon Jan 01, 1990 12:00 am
- Location: LONDON UK
Re: Edith update
Cannot comment on the new spring and its tangs but the kickstart on my AMC box needs assistance to return to the correct position after starting. Just got used to it!
clive
if it ain't broke don't fix
if it ain't broke don't fix
-
- Member
- Posts: 1906
- Joined: Wed Jan 01, 1992 12:00 am
- Location: SURREY UK
Re: Edith update
Have the same problem with the Model 31, must be something to do with the new springs that are being made these days.
- Harry44
- Member
- Posts: 280
- Joined: Sat Dec 17, 2016 5:26 pm
- Location: SOMERSET UK
Re: Edith update
Yeah thanks for the replies. Perhaps this is why they modified the spring and its fixings on the later Norton gearboxes.
Thinking cap on
Thinking cap on
si is does non opportunus vos postulo a maior pango
-
- Posts: 157
- Joined: Tue Mar 29, 2016 7:19 pm
- Location: CALVADOS FRANCE
Re: Edith update
Hello,I'm still at the"start it with no exhaust and ride it round the yard to anno-", no, I mean "test" my G80 so I'm no guru, BUT my gearbox was in pieces when I bought the bike and when I tried to find how to tension the kickstart the manual merely told me to replace it in the same position as I had removed it!Very helpful. I wound it one turn and fitted it, a bit floppy and it returned unreliably mainly returning to horizontal, no good for the requisite"long swinging kick" to start the bike. So gearbox end off and another turn added (three turns binds the spring ) and now it returns reliably and feels solid on returning, so have you tried two turns? Also, why are you changing the spring if it does work ? Is it cracking or showing imminent signs of failure? Your replacement doesn't seem up to the job.
Have fun anyway, DT.
Have fun anyway, DT.
- Harry44
- Member
- Posts: 280
- Joined: Sat Dec 17, 2016 5:26 pm
- Location: SOMERSET UK
Re: Edith update
I changed the spring because it didn't return the kick start. But it does hold it up when pulled back up by hand.
Have fun annoying the neighbours
Have fun annoying the neighbours
si is does non opportunus vos postulo a maior pango