My toolbox needs saving!
-
- Posts: 208
- Joined: Sat Sep 07, 2019 5:51 pm
- Location: Hampshire UK
My toolbox needs saving!
The toolbox on my ‘56 G80S has seen better days, the shed it was dragged out of hadn't been kind to the tinwork. The box is largely solid but the bottom is very rusty with a few holes. I'm not interested in making it pristine, the bike is going to wear its age with pride, but I would like to find a way of fixing the hinge and lid if possible!
Suggestions please....!
Suggestions please....!
Last edited by markwhitelock on Thu Apr 09, 2020 2:39 pm, edited 1 time in total.
-
- Posts: 2884
- Joined: Mon Mar 24, 2014 5:44 pm
- Location: Aberdeenshire
Re: My toolbox needs saving!
Hi
The best method would be to cut out the damage, fabricate an insert and weld it into place - rather a skilled operation and will be expensive to get done correctly if you can't do it yourself.
A more DIY friendly approach would be to de-rust the box and carry out a patch repair. To de-rust it I would use electrolysis, there's plenty of info on the interweb, here for example:
https://www.robotroom.com/Rust-Removal.html
Carefully grind/file off the remnants of the hinge.
Cut some sheet steel to size and profile to cover the base of the toolbox from the inside and a strip to do the same for the lid and bond these into place using epoxy structural adhesive:
https://www.silmid.com/adhesives/epoxy- ... e-6oz-kit/
Fill the outer surfaces in preparation for paint, you can use metalset for this but it does not sand as easily as body filler.
Cut a piece of piano hinge to suit and attach with pop rivets.
Spray black.
Regards Mick
The best method would be to cut out the damage, fabricate an insert and weld it into place - rather a skilled operation and will be expensive to get done correctly if you can't do it yourself.
A more DIY friendly approach would be to de-rust the box and carry out a patch repair. To de-rust it I would use electrolysis, there's plenty of info on the interweb, here for example:
https://www.robotroom.com/Rust-Removal.html
Carefully grind/file off the remnants of the hinge.
Cut some sheet steel to size and profile to cover the base of the toolbox from the inside and a strip to do the same for the lid and bond these into place using epoxy structural adhesive:
https://www.silmid.com/adhesives/epoxy- ... e-6oz-kit/
Fill the outer surfaces in preparation for paint, you can use metalset for this but it does not sand as easily as body filler.
Cut a piece of piano hinge to suit and attach with pop rivets.
Spray black.
Regards Mick
- Duncan
- Member
- Posts: 2137
- Joined: Thu Jul 10, 2003 1:00 am
- Location: HAMPSHIRE UK
Re: My toolbox needs saving!
Later tool boxes used a 2 slot and finger arrangement with a loose cover, it might be possible to convert to a similar. For information, the tool box cover does not appear to have flutes on it so it would be a 1956 model year fitting.
-
- Member
- Posts: 3365
- Joined: Wed Oct 12, 2005 10:45 pm
- Location: N YORKS UK
Re: My toolbox needs saving!
I think Duncan is right, it looks the same as my original toolbox. These are hard to come by so I would take steps to save it if you can. Thanks to MickD for the linke to electrically removing rust, I think I shall be giving that a go.
Good luck with the job.
Johnny B
Good luck with the job.
Johnny B
-
- Posts: 208
- Joined: Sat Sep 07, 2019 5:51 pm
- Location: Hampshire UK
Re: My toolbox needs saving!
Hi Duncan, yes it is a ‘56 bike, I put the wrong year in my post!Duncan wrote:Later tool boxes used a 2 slot and finger arrangement with a loose cover, it might be possible to convert to a similar. For information, the tool box cover does not appear to have flutes on it so it would be a 1956 model year fitting.
The lid does stay on with the screw, but I wouldn't risk putting anything vital in there!! I definitely want to keep it as original as possible.
-
- Member
- Posts: 3365
- Joined: Wed Oct 12, 2005 10:45 pm
- Location: N YORKS UK
Re: My toolbox needs saving!
Have to say (touches wood) that the screw has never come undone on mine and I've done plenty of miles.
In the early days of trips up and down the country that's where my tools were.
With the Al osbourne regulator, the flassher unit and something else which I can't recall offhand, there's not so much room now.
Johnny B
In the early days of trips up and down the country that's where my tools were.
With the Al osbourne regulator, the flassher unit and something else which I can't recall offhand, there's not so much room now.
Johnny B
- Cjay59_LAPSED
- Posts: 520
- Joined: Mon Nov 05, 2012 3:43 pm
- Location: Cork, Ireland
- Contact:
Re: My toolbox needs saving!
I managed to get a '56' Tool box from the Australian Ebay, bit pricy, but left side no flutes, they suffered from rusting due to leaky batteries but examples can be found in dryer climates.
-
- Posts: 208
- Joined: Sat Sep 07, 2019 5:51 pm
- Location: Hampshire UK
Re: My toolbox needs saving!
One in there now but over £100, bit eye wateringCjay59 wrote:I managed to get a '56' Tool box from the Australian Ebay, bit pricy, but left side no flutes, they suffered from rusting due to leaky batteries but examples can be found in dryer climates.
-
- Member
- Posts: 3365
- Joined: Wed Oct 12, 2005 10:45 pm
- Location: N YORKS UK
Re: My toolbox needs saving!
Disappointed to be proved right. Do the best with what you have is my not very helpful advice. Use MickD's post.
Johnny B
Johnny B
-
- Member
- Posts: 39
- Joined: Mon May 14, 2018 9:56 am
- Location: Queensland AUSTRALIA
Re: My toolbox needs saving!
Google "Piano hinge" stainless steel one would help to avoid rust.