no oil returning to the tank
-
- Member
- Posts: 3369
- Joined: Wed Oct 12, 2005 10:45 pm
- Location: N YORKS UK
Re: no oil returning to the tank
Wow!
You've certainly had a close shave after all.
We all bodge things sometimes, particularly when hundreds of miles from home and abroad. Usually put it right as soon as safely back though.
Then there's the things we just aren't easily able to fix. I have a very weak thread on the plate where the oil feed for the rocker box is where it comes off the crancase. And the little bolt is non standard. It's up against the crankcase and not a job I'm fixing soon unless I get a spare engine.
Unlike some of the more affluent Members, multiple motorcycles and vast stocks of hoarded spares aren't a possibility (setting aside the spare Burman and two spare SR1s).
Johnny B
You've certainly had a close shave after all.
We all bodge things sometimes, particularly when hundreds of miles from home and abroad. Usually put it right as soon as safely back though.
Then there's the things we just aren't easily able to fix. I have a very weak thread on the plate where the oil feed for the rocker box is where it comes off the crancase. And the little bolt is non standard. It's up against the crankcase and not a job I'm fixing soon unless I get a spare engine.
Unlike some of the more affluent Members, multiple motorcycles and vast stocks of hoarded spares aren't a possibility (setting aside the spare Burman and two spare SR1s).
Johnny B
- Pharisee
- Member
- Posts: 1127
- Joined: Tue Mar 15, 2016 8:51 pm
- Location: Lincolnshire UK
- Contact:
Re: no oil returning to the tank
Could be that the PO has put in 1/4" x 1/4" rollers instead of the correct ones that are 1/4" diameter but a few thou shorter.willowbedone wrote:I wondered why the clutch centre nut was finger tight Now I know why tighten it up and the clutch jams solid Another problem to sort
I'm from the Fens.... Gimme six.
-
- Member
- Posts: 3369
- Joined: Wed Oct 12, 2005 10:45 pm
- Location: N YORKS UK
Re: no oil returning to the tank
There've been threads about this roller business:
http://www.jampot.com/forum/viewtopic.p ... ch+rollers
might be of interest.
Johnny B
http://www.jampot.com/forum/viewtopic.p ... ch+rollers
might be of interest.
Johnny B
-
- Member
- Posts: 191
- Joined: Mon Nov 16, 2015 6:08 pm
- Location: east sussex
Re: no oil returning to the tank
Clutch sorted
Barrell back in place Tomorrow I will be timing the mag and fitting the cylinder head That's after checking head bolts are not bottoming out as when I look at a couple of them there is evidence of it
![Very Happy :D](./images/smilies/icon_e_biggrin.gif)
-
- Member
- Posts: 191
- Joined: Mon Nov 16, 2015 6:08 pm
- Location: east sussex
Re: no oil returning to the tank
All getting back together Looking forward to attending the February Sussex section meeting Hope it's not snowing as it's a few miles journey
-
- Member
- Posts: 8560
- Joined: Wed Sep 01, 2004 1:00 am
- Location: WEST SUSSEX UK
Re: no oil returning to the tank
Well done, Ian. Excellent progress.
You'll be made most welcome at the Feb meeting which also happens to be our annual 'Bits in the Bag' event (don't ask). Don't be put off though; it's only a very casual and light-hearted bit o' fun and there'll be plenty of time to chat.
You'll be made most welcome at the Feb meeting which also happens to be our annual 'Bits in the Bag' event (don't ask). Don't be put off though; it's only a very casual and light-hearted bit o' fun and there'll be plenty of time to chat.
'There is a tide in the affairs of men
Which taken at the flood............'
Which taken at the flood............'
-
- Member
- Posts: 191
- Joined: Mon Nov 16, 2015 6:08 pm
- Location: east sussex
Re: no oil returning to the tank
Head back on ignition timing set Rocker cover fitted .And yes another worn out part exhaust valve lifter lever is worn meaning the angle is all wrong . I recon po had overtightened the cable which meant the rocker arm has worn the levers shaft .I have poured the suggested amount oil down each pushrod tube and liberly oiled parts as I reassemble them .The auto advance units springs look well worn ( is anyone knows the part number for these please let me know ).Tomorrow I'm of to a mate's to help sort his bsa wb30 which is running rough
It's all good fun
It's all good fun
-
- Member
- Posts: 191
- Joined: Mon Nov 16, 2015 6:08 pm
- Location: east sussex
Re: no oil returning to the tank
Help I've spent hours now cleaning the oil tank but still getting swarf and a load of gummy looking black oil residue Any one with a good way to get this all out please let me know . I've replaced advance retard springs and it's working correctly now After a trip to kempton park Saturday for a few bits and pieces I am hoping to start the bike next week
-
- Posts: 2886
- Joined: Mon Mar 24, 2014 5:44 pm
- Location: Aberdeenshire
Re: no oil returning to the tank
Hi
My preferred method of cleaning tanks is to use a solvent and a length of chain - for an oil tank I'd use a couple of feet of 1/4" ish general purpose DIY shed chain. The advantage of using chain as an agitator is that you know there's nothing left in the tank after you've removed it, not the case with nuts and bolts etc.
As for solvent, use whatever you have lying around / access to, petrol , paraffin etc.
Regards Mick
My preferred method of cleaning tanks is to use a solvent and a length of chain - for an oil tank I'd use a couple of feet of 1/4" ish general purpose DIY shed chain. The advantage of using chain as an agitator is that you know there's nothing left in the tank after you've removed it, not the case with nuts and bolts etc.
As for solvent, use whatever you have lying around / access to, petrol , paraffin etc.
Regards Mick
-
- Member
- Posts: 3369
- Joined: Wed Oct 12, 2005 10:45 pm
- Location: N YORKS UK
Re: no oil returning to the tank
Good luck, you deserve some after the effort you've put in.
The chain tip sounds good.
Johnny B
The chain tip sounds good.
Johnny B