1954 G80 Rear Brake Problem
-
- Posts: 111
- Joined: Sat Nov 26, 2005 10:47 pm
- Location: WEST MIDLANDS UK
Re: 1954 G80 Rear Brake Problem
It is clear that the expanding ends of the shoes are twisting outwards as the cam is operated. My understanding is that the fixed end of the shoes should be snug on the pivot pin, I.e. they should not be able to twist outwards to any extent. This inability to twist effectively prevents the expanding end from sliding off the cam. So I think you need to check how snug the shoes are on the pivot. Too much side play or the ability to twist significantly on the pivot may well be the problem. A bit of filing may solve the problem if the shoes do not rest smoothly and tightly on the pivot.
-
- Posts: 19
- Joined: Thu Feb 08, 2018 10:27 am
- Location: LEICESTERSHIRE UK
Re: 1954 G80 Rear Brake Problem
Its the one that came with the bike.
- ajscomboman
- Member
- Posts: 3958
- Joined: Mon Jan 01, 1990 12:00 am
- Location: HAMPSHIRE UK
Re: 1954 G80 Rear Brake Problem
I'm intrigued, please expand more on the condition of the shoes and reason for refusal, also can you post some pictures of the shoes please.mrpjhancock wrote:Iv tried the spring thing with no luck . . . . I was at the AMOC parts shop today and tried exchanging my brake shoes for some new ones. Unfortunately my shoes werent good enough to exchange. Apparently they need to be in perfect condition!
So Im stuck with the ones I have
I have attached a photo of the brake drum its self. looks like its the hardened pads that are coming into contact
-
- Posts: 19
- Joined: Thu Feb 08, 2018 10:27 am
- Location: LEICESTERSHIRE UK
Re: 1954 G80 Rear Brake Problem
It was explained to me that the reason refusing exchange is the fact that the machining for the hardened pads has broken out the casting.
You do not have the required permissions to view the files attached to this post.
-
- Posts: 19
- Joined: Thu Feb 08, 2018 10:27 am
- Location: LEICESTERSHIRE UK
Re: 1954 G80 Rear Brake Problem
Does anyone have a set of old brake shoes they want to sell . . . . . doesnt matter if they are worn out . . . . I would use them to exchange for recon ones .. .
-
- Posts: 2884
- Joined: Mon Mar 24, 2014 5:44 pm
- Location: Aberdeenshire
Re: 1954 G80 Rear Brake Problem
Hi
Your shoes are machined in the same manner as mine - I believe this is as per design, I think someone at AMOC Spares has made a mistake.
Why not try putting a thin shim between the brake plate and shoes at the pivot pin? this should reduce the tendency for the shoes to migrate.
Regards Mick
Your shoes are machined in the same manner as mine - I believe this is as per design, I think someone at AMOC Spares has made a mistake.
Why not try putting a thin shim between the brake plate and shoes at the pivot pin? this should reduce the tendency for the shoes to migrate.
Regards Mick
- ajscomboman
- Member
- Posts: 3958
- Joined: Mon Jan 01, 1990 12:00 am
- Location: HAMPSHIRE UK
Re: 1954 G80 Rear Brake Problem
I'll take up the case, there appears to be no reason for the refusal other than the pin end. That in itself will have no detrimental effect on the shoe and won't be any problem re-lining them.mrpjhancock wrote:It was explained to me that the reason refusing exchange is the fact that the machining for the hardened pads has broken out the casting.
-
- Member
- Posts: 8559
- Joined: Wed Sep 01, 2004 1:00 am
- Location: WEST SUSSEX UK
Re: 1954 G80 Rear Brake Problem
Did you have this problem with the previous cam and bought the replacement to try to cure the rubbing issue?
Before (and after operating the brake) your cam isn't covering (acting upon) the whole face of the hardened mushroom but only on the lower part. Could that be the reason why the cam is tending to lift/twist the shoe(s)? It seems that the cam isn't tall enough.
Here's my front brake and you can see that when at rest the cam covers all the face of the hardened mushroom. Could you try raising the cam by putting a washer under it and still have enough shaft exposed to fit the outer operating arm (perhaps needing a spacer collar on the outside to prevent it locking up)?
Before (and after operating the brake) your cam isn't covering (acting upon) the whole face of the hardened mushroom but only on the lower part. Could that be the reason why the cam is tending to lift/twist the shoe(s)? It seems that the cam isn't tall enough.
Here's my front brake and you can see that when at rest the cam covers all the face of the hardened mushroom. Could you try raising the cam by putting a washer under it and still have enough shaft exposed to fit the outer operating arm (perhaps needing a spacer collar on the outside to prevent it locking up)?
You do not have the required permissions to view the files attached to this post.
'There is a tide in the affairs of men
Which taken at the flood............'
Which taken at the flood............'
-
- Posts: 19
- Joined: Thu Feb 08, 2018 10:27 am
- Location: LEICESTERSHIRE UK
Re: 1954 G80 Rear Brake Problem
Yes my intention was to replace the cam, springs and shoes. I thought perhaps because there was some play in the cam shaft through the back plate it was twisting the cam movement and lifting the shoes. The cam is definitely the correct one as its identical to the old one (minus the worn shaft of course)
- Pharisee
- Member
- Posts: 1127
- Joined: Tue Mar 15, 2016 8:51 pm
- Location: Lincolnshire UK
- Contact:
Re: 1954 G80 Rear Brake Problem
Those shoes look identical to the ones I took to AMC Classic Spares and exchanged for a relined set with no problem at all.mrpjhancock wrote:It was explained to me that the reason refusing exchange is the fact that the machining for the hardened pads has broken out the casting.
I'm from the Fens.... Gimme six.