Cylinder liner / Alloy Barrel for G80S
-
- Posts: 86
- Joined: Fri Jul 03, 2015 4:16 pm
- Location: LEICS UK
Cylinder liner / Alloy Barrel for G80S
Hello
I have just stripped down my recently purchased 1956 G80S and found that the barrel is scored and has two large gouges in it where presumably the gudgeon pin has tried to make a break for freedom
I understand that I might have the option of getting the barrel lined or I see that you can still get the Alloy G80CS barrels
A couple of qurstions
Can anybody reccomend who could line the existing barrel and what piston should i use, the piston in the engine looks ok and has 10197 +20 on it. I do not think this is the piston that did the damage
Also can the Alloy barrel be used on a G80S - i see the bores are diffeent 82mm versus 86mm
Any assistance would be much appreciated
Thanks in advance
I have just stripped down my recently purchased 1956 G80S and found that the barrel is scored and has two large gouges in it where presumably the gudgeon pin has tried to make a break for freedom
I understand that I might have the option of getting the barrel lined or I see that you can still get the Alloy G80CS barrels
A couple of qurstions
Can anybody reccomend who could line the existing barrel and what piston should i use, the piston in the engine looks ok and has 10197 +20 on it. I do not think this is the piston that did the damage
Also can the Alloy barrel be used on a G80S - i see the bores are diffeent 82mm versus 86mm
Any assistance would be much appreciated
Thanks in advance
......
- dave16mct
- Member
- Posts: 3243
- Joined: Mon Jan 01, 1990 12:00 am
- Location: LANCASHIRE UK
Re: Cylinder liner / Alloy Barrel for G80S
You cannot use the G80CS barrell without major changes as the stud spacing is different, different stroke etc. I would ask T&L engineering about a rebore or relining. O/S Pistons are available at club spares.
Cheers Dave
Cheers Dave
- Les Howard
- Posts: 1017
- Joined: Sat Jan 07, 2012 9:57 am
- Location: Somerset UK
Re: Cylinder liner / Alloy Barrel for G80S
Yes ...the new alloy barrels are for the later post '64 engines...86mm bore which has to be used with later head and piston ATB...Les
-
- Posts: 86
- Joined: Fri Jul 03, 2015 4:16 pm
- Location: LEICS UK
Re: Cylinder liner / Alloy Barrel for G80S
Thanks for your very quick replies, just spoke to T&L who were very helpful - brilliant !
......
-
- Member
- Posts: 243
- Joined: Sat Jan 01, 1994 12:00 am
- Location: Newzealand NEW ZEALAND
Re: Cylinder liner / Alloy Barrel for G80S
Yes ...the new alloy barrels are for the later post '64 engines...86mm bore which has to be used with later head and piston ATB...Les
Hi Les
The short stroke barrel was introduced in '56. Not being picky, but someone planning a similar conversion may get the wrong idea
Cheers Marty
Hi Les
The short stroke barrel was introduced in '56. Not being picky, but someone planning a similar conversion may get the wrong idea
Cheers Marty
-
- Member
- Posts: 476
- Joined: Sat Oct 26, 2013 9:09 pm
- Location: CAMBRIDGESHIRE UK
Re: Cylinder liner / Alloy Barrel for G80S
I keep getting a strange urge to try a cut down 500 ally barrel on a 63 interim, (short stroke), motor. The only problem being that I don't want to muck about with a very nice original bike.
I suppose it would be best if I just keep taking the pills eh.
I suppose it would be best if I just keep taking the pills eh.
- Rob Harknett
- Member
- Posts: 11236
- Joined: Mon Jan 01, 1990 12:00 am
- Location: ESSEX UK
Re: Cylinder liner / Alloy Barrel for G80S
Don't think its the pills. Not taking any so I can't blame them. It was years before I finally brought a bike I always wanted back in my teens. Now I've got such a bike, I don't like riding it. At first it was a novelty to have power to spare. Now I seem to pick a 350 single or old prewar bike when I feel like a ride out. If it is the pills,I think I better keep off them else I'll never get out for a ride, if I get the urge to change bits on a bike.
- ajscomboman
- Member
- Posts: 3971
- Joined: Mon Jan 01, 1990 12:00 am
- Location: HAMPSHIRE UK
Re: Cylinder liner / Alloy Barrel for G80S
Are you referring to the 63 CSR Rob. I always wanted a 500 CS and now I've got one the bloody thing has been a nightmare to set up, even now it's developed a stutter coming off pilot onto the slide and I can't tune it out. Its spoiling my enjoyment of what should be a cracking bike. The 350 CS short stroke I've just re-commissioned is the opposite, less power but a true giggle to ride. Revs like buggery and has the crispest exhaust note, true hooligans bike! I'm contemplating taking both to the Jampot.Rob Harknett wrote:Don't think its the pills. Not taking any so I can't blame them. It was years before I finally brought a bike I always wanted back in my teens. Now I've got such a bike, I don't like riding it. At first it was a novelty to have power to spare. Now I seem to pick a 350 single or old prewar bike when I feel like a ride out. If it is the pills,I think I better keep off them else I'll never get out for a ride, if I get the urge to change bits on a bike.
-
- Member
- Posts: 3549
- Joined: Sun Jan 01, 1995 12:00 am
- Location: ESSEX UK
Re: Cylinder liner / Alloy Barrel for G80S
I'm contemplating taking both to the Jampot.[/quote]
Good that will mean I can charge you double
Good that will mean I can charge you double
Roy
- ajscomboman
- Member
- Posts: 3971
- Joined: Mon Jan 01, 1990 12:00 am
- Location: HAMPSHIRE UK
Re: Cylinder liner / Alloy Barrel for G80S
Don't be silly, I thought it'd mean I was getting a bargain only paying 1/2 price entry for each bike.