ENGINE IDENTITY.
- Rob Harknett
- Member
- Posts: 11211
- Joined: Mon Jan 01, 1990 12:00 am
- Location: ESSEX UK
Re: ENGINE IDENTITY.
All useful knowledge John, also Robs comment about CS engines all being short stroke after 1955 ?? There, I've forgotten all ready. 55 ? But I and anyone else can still check literature. I am afraid in most areas of bike knowledge, I tend to forget a lot, but I do know where I could find the answer.
- ajscomboman
- Member
- Posts: 3958
- Joined: Mon Jan 01, 1990 12:00 am
- Location: HAMPSHIRE UK
Re: ENGINE IDENTITY.
But only in 500 cc capacity, the factory still continued to produce both short and long stroke motors in 350cc form. The long stroke being mainly for trials and the short stroke as a scrambler. All good fun delving into AMC history. It's not always clear cut as factory odd balls do crop up now and again but the history in the archives is pretty much spot on most of the time.Rob Harknett wrote:All useful knowledge John, also Robs comment about CS engines all being short stroke after 1955 ?? There, I've forgotten all ready. 55 ? But I and anyone else can still check literature. I am afraid in most areas of bike knowledge, I tend to forget a lot, but I do know where I could find the answer.
- Rob Harknett
- Member
- Posts: 11211
- Joined: Mon Jan 01, 1990 12:00 am
- Location: ESSEX UK
Re: ENGINE IDENTITY.
I just had a look at 350's that is a bit of a mine field. Some std road models short and long stroke. There's 81 mm 85.5 and 93mm strokes. Includes light weight 350 also. plus 347 & 348 cc. There are also literature errors?? e.g 56 / 57 349cc 7R, stroke 78 mm. prior to that 348 cc was 18 mm stroke, yes 18 mm that has to be wrong surely. You also have to be careful how you read this literature e.g dates given, except for the start of civi production in 1945, early post war the calendar year was used. When the London shows started up again , they reverted back to the model year starting Sept 1st. To get the next year models read for the motor cycle show first week of Nov. So where you see Sept. 55 That's the 56 model.ajscomboman wrote:But only in 500 cc capacity, the factory still continued to produce both short and long stroke motors in 350cc form. The long stroke being mainly for trials and the short stroke as a scrambler. All good fun delving into AMC history. It's not always clear cut as factory odd balls do crop up now and again but the history in the archives is pretty much spot on most of the time.Rob Harknett wrote:All useful knowledge John, also Robs comment about CS engines all being short stroke after 1955 ?? There, I've forgotten all ready. 55 ? But I and anyone else can still check literature. I am afraid in most areas of bike knowledge, I tend to forget a lot, but I do know where I could find the answer.
You do not have the required permissions to view the files attached to this post.
-
- Member
- Posts: 69
- Joined: Mon Jan 01, 1990 12:00 am
- Location: NORWAY
Re: ENGINE IDENTITY.
The engine number and CS suffix are correct for a 1957 AJS "short stroke" 86mm bore x 85.5mm stroke.
As John Jarret points out, the timing side case for these engines has a roller bearing in addition to the oil distributor bush. See the enclosed photos.
As you probably are aware, the CS engines have different crankshaft/flywheels, cylinder, piston, cylinder head, cams, push rods, etc. than the standard long stroke models. Happy parts hunting!
Bjørn
You do not have the required permissions to view the files attached to this post.
- GOLDSTAR
- Member
- Posts: 2521
- Joined: Thu Sep 11, 2003 1:00 am
- Location: KENT UK
Re: ENGINE IDENTITY.
I am led to believe that the short stroke CS engine had the bottom end of a 7R, if this is so it does give you a little more scope to obtain parts, kind rergards
-
- Member
- Posts: 69
- Joined: Mon Jan 01, 1990 12:00 am
- Location: NORWAY
Re: ENGINE IDENTITY.
As far as I am aware, the only component on a 7R crankshaft which was also used on the CS models is the crankpin.
Stroke for the 7R is 81mm prior to 1956 and 78mm thereafter, compared to the 85.5mm for the CS. Flywheels and axles are different and the 7R con rod is shorter than for the CS models.
Bjørn
Stroke for the 7R is 81mm prior to 1956 and 78mm thereafter, compared to the 85.5mm for the CS. Flywheels and axles are different and the 7R con rod is shorter than for the CS models.
Bjørn
- GOLDSTAR
- Member
- Posts: 2521
- Joined: Thu Sep 11, 2003 1:00 am
- Location: KENT UK
Re: ENGINE IDENTITY.
thanks Bjorn, thats sorted it then, and come to think of it 'tis probably what I was informed. kind regards