Oil again
-
- Member
- Posts: 1102
- Joined: Tue Jan 15, 2008 4:18 pm
- Location: SOMERSET UK
Oil again
I've been using Halfords 20/50 Classic oil for quite a while in the engine and AMC gearbox
I notice the gear changes are a bit tighter during a longish run, with the engine hot.
Would this be down to using this oil rather than the recommended Castro's Sae 50 as stated in the manual.
Is there a lot of difference between the two.
If Sae 50 is heavier maybe this could help improve the gear change.
I was thinking about trying this...
https://www.ebay.co.uk/itm/Silkolene-Ha ... 2539129632
I notice the gear changes are a bit tighter during a longish run, with the engine hot.
Would this be down to using this oil rather than the recommended Castro's Sae 50 as stated in the manual.
Is there a lot of difference between the two.
If Sae 50 is heavier maybe this could help improve the gear change.
I was thinking about trying this...
https://www.ebay.co.uk/itm/Silkolene-Ha ... 2539129632
Mike
- Rob Harknett
- Member
- Posts: 11236
- Joined: Mon Jan 01, 1990 12:00 am
- Location: ESSEX UK
Re: Oil again
No, just the opposite. Note in extreme cold SAE 30 is recommended. Where is heaviness felt? If when using the clutch lever, perhaps your thrust rod is seizing. When was the last time you inspected and cleaned it. Could be the multi grade has loosened muck. If you put it in the gearbox without first given it a good clean. Why did you decide not to use the recommended grade. Could be that what's caused the problem. So the box now needs all the loose muck cleaned out and correct oil put back in. Let it drain over night and see what comes out.
-
- Member
- Posts: 8542
- Joined: Wed Sep 01, 2004 1:00 am
- Location: WEST SUSSEX UK
Re: Oil again
I've never found any 'muck' in any of my gearboxes. In fact the drained oil is always as clean as when it went in. It's cleanliness is an easy way to tell whether oil drips on the ground are from the engine or the gearbox.Rob Harknett wrote: So the box now needs all the loose muck cleaned out and correct oil put back in. Let it drain over night and see what comes out.
I cannot see any justification for using multigrade in the gearbox.
'There is a tide in the affairs of men
Which taken at the flood............'
Which taken at the flood............'
- Rob Harknett
- Member
- Posts: 11236
- Joined: Mon Jan 01, 1990 12:00 am
- Location: ESSEX UK
Re: Oil again
Could be because you use your bikes Neville. Standing bikes can get oil contaminated with moisture, the oil turn milky. May not even drain out easily. Always need a bit of oil in my old grease gear boxes after standing. Also spay WD 40 in oil boxes to lubricate parts that have stood dry.SPRIDDLER wrote:I've never found any 'muck' in any of my gearboxes. In fact the drained oil is always as clean as when it went in. It's cleanliness is an easy way to tell whether oil drips on the ground are from the engine or the gearbox.Rob Harknett wrote: So the box now needs all the loose muck cleaned out and correct oil put back in. Let it drain over night and see what comes out.
I cannot see any justification for using multigrade in the gearbox.
-
- Posts: 2886
- Joined: Mon Mar 24, 2014 5:44 pm
- Location: Aberdeenshire
Re: Oil again
Hi
The bigger the number the 'thicker' the oil. Theoretically 20 / 50 multigrade will have the same properties as straight 50 when both are at normal running temperature, however when cold the 20 / 50 equates to a straight 20, (eg thinner).
The range of operating temperature in a gearbox is probably lower than that of the engine and therefore a 20 / 50 multigrade is more than likely performing at less than 50 viscocity, (thickness), so in my opinion could be contributing to your tighter feeling gearbox.
I'm a bit of a traditionalist so am using Castrol XP50 in my gearbox and Castrol XL30 in the engine, (though if Scottish summers continue to get warmer I might change to SAE50 engine oil).
Regards Mick
The bigger the number the 'thicker' the oil. Theoretically 20 / 50 multigrade will have the same properties as straight 50 when both are at normal running temperature, however when cold the 20 / 50 equates to a straight 20, (eg thinner).
The range of operating temperature in a gearbox is probably lower than that of the engine and therefore a 20 / 50 multigrade is more than likely performing at less than 50 viscocity, (thickness), so in my opinion could be contributing to your tighter feeling gearbox.
I'm a bit of a traditionalist so am using Castrol XP50 in my gearbox and Castrol XL30 in the engine, (though if Scottish summers continue to get warmer I might change to SAE50 engine oil).
Regards Mick
- Rob Harknett
- Member
- Posts: 11236
- Joined: Mon Jan 01, 1990 12:00 am
- Location: ESSEX UK
Re: Oil again
Mick surely thinner oil will allow moving parts to run more freely, That's why in extreme cold 30 SAE is recommended for the gear box. So using 20/50 the box should run more freely. ( put thick oil in a clockwork watch would stop it ) One reason I went for oil being contaminated, as it was feeling heavy. Or of cause its the clutch thats heavy due to thrust rod seizing perhaps.
-
- Member
- Posts: 8542
- Joined: Wed Sep 01, 2004 1:00 am
- Location: WEST SUSSEX UK
Re: Oil again
Why? 'Ordinary' Morris mono oil is fine (and less expensive).mikeydpippin wrote:I was thinking about trying this...
https://www.ebay.co.uk/itm/Silkolene-Ha ... 2539129632
I and probably hundreds of thousands of others have used straight SAE 50 in AMC, Burman and other 'boxes quite happily ever since mother was a lad.
If the gearchange is unusually stiff I suggest the problem is not with the oil.
The AMC 'box is pretty bombproof. A factory tester who was visiting our section said that when he was sent out on a bike fitted with the first production 'box he was offered a fiver if he could break it. He tried, as a fiver was probably a week's wages.
Out of interest what oil do you put in the primary chaincase?
'There is a tide in the affairs of men
Which taken at the flood............'
Which taken at the flood............'
-
- Member
- Posts: 1102
- Joined: Tue Jan 15, 2008 4:18 pm
- Location: SOMERSET UK
Re: Oil again
Thanks for the info Nev,
The gearbox changes gears as it should until after a good run.
Then as the gearbox warms up it changes gear albeit seems a bit dry and not so easy to change.
I use 20/w50 in the primary chaincase as well.
Think I will use up the 20w50 in the engine and when used I will change all the oil to sae50
The gearbox changes gears as it should until after a good run.
Then as the gearbox warms up it changes gear albeit seems a bit dry and not so easy to change.
I use 20/w50 in the primary chaincase as well.
Think I will use up the 20w50 in the engine and when used I will change all the oil to sae50
Mike
-
- Posts: 2886
- Joined: Mon Mar 24, 2014 5:44 pm
- Location: Aberdeenshire
Re: Oil again
Hi RobRob Harknett wrote:Mick surely thinner oil will allow moving parts to run more freely
You're correct to a point, but thinner oils have a thinner lubricating layer and this is easier to break through resulting in metal to metal contact, more wear and friction, (stiffer operation). In a gearbox where there is no pressurised oil system I would prefer to use a more viscous monograde.
Regards Mick
- 1608
- Member
- Posts: 2493
- Joined: Mon Oct 05, 2009 1:00 am
- Location: ESSEX UK
Re: Oil again
Mikey, if its for your 350's then the general consensus is straight 50 for the engine mainly because it has big end roller bearings as opposed to shells. The gear box should also have a heavy grade as recommended straight 50. If its anything like any of my bikes then the gearboxes hardly warm up at all. So, the 20/50 will not reach its heavier properties more suitable for the heavy demands/loads of the g/box.