1957 M16 not running properly
-
- Posts: 48
- Joined: Tue Jun 02, 2015 4:57 pm
- Location: Wales
Re: 1957 M16 not running properly
Andy, it may be worth checking that there isn't an air leak somewhere – the face where the carb meets the cylinder can sometimes be slightly warped through over tightening. The other thing that comes to mind is that the float height may be wrong and therefore giving an incorrect fuel level in the carb. On amals the pip on the float chamber cover indicates the correct fuel level – see how to check it, along with a few other tips, here: http://www.whfolk.co.uk/REOCHUMBER/Arti ... nobloc.htm
Sean
Sean
- Janet
- Member
- Posts: 4147
- Joined: Mon Jan 01, 1996 12:00 am
- Location: EAST YORKSHIRE UK
Re: 1957 M16 not running properly
Caveat: I know nothing but............
Doesn't flames from the carb suggest the inlet valve may be open when the plug is sparking?
Doesn't flames from the carb suggest the inlet valve may be open when the plug is sparking?
-
- Member
- Posts: 335
- Joined: Mon Jan 01, 1990 12:00 am
- Location: GWENT UK
Re: 1957 M16 not running properly
I know that the carb is still probably the issue, but is the advance and retard unit moving freely? I ask this because of the spitting back. May help, LynP
- clanger9
- Posts: 1165
- Joined: Sat Jun 20, 2015 9:38 am
- Location: Chester, UK
Re: 1957 M16 not running properly
It can also be caused by liquid fuel/droplets - which can happen if the idle jet isn't atomising the fuel properly (or if the inlet manifold is cold).Janet wrote:Doesn't flames from the carb suggest the inlet valve may be open when the plug is sparking?
My CSR hasn't got a choke, so it spits nice flames from the carb when started from cold...
1989 Moto Morini Dart 350
1993 Ducati 750SS
1993 Ducati 750SS
-
- Deceased
- Posts: 598
- Joined: Sun Oct 07, 2018 11:36 pm
- Location: Essex UK
Re: 1957 M16 not running properly
I took the advance/retard unit off yesterday and it's free, especially after lubricating it, I remember from experience with my Enfield 250 many year ago, when the bob weights stuck wide open. I retimed it after that.
I'm still puzzled, but will get back to it tomorrow
Andy
I'm still puzzled, but will get back to it tomorrow
Andy
- clanger9
- Posts: 1165
- Joined: Sat Jun 20, 2015 9:38 am
- Location: Chester, UK
Re: 1957 M16 not running properly
As others have said:
1. Check the float height
2. Check the idle jet is clear
3. Check it's got the right slide cutaway
Any of the above can produce the symptoms you describe...
Good luck!
1. Check the float height
2. Check the idle jet is clear
3. Check it's got the right slide cutaway
Any of the above can produce the symptoms you describe...
Good luck!
1989 Moto Morini Dart 350
1993 Ducati 750SS
1993 Ducati 750SS
-
- Deceased
- Posts: 598
- Joined: Sun Oct 07, 2018 11:36 pm
- Location: Essex UK
Re: 1957 M16 not running properly
I must admit I am not sure how to check the float height. If so how do I alter it if it's not correct as there's not anything to bend? Thanks
- clanger9
- Posts: 1165
- Joined: Sat Jun 20, 2015 9:38 am
- Location: Chester, UK
Re: 1957 M16 not running properly
Aha.
You mentioned you replaced the float valve? It's a good idea to check the float level after doing that...
- Take off the idle jet cover nut
- Push a length of clear pipe over the idle jet
- Hold the pipe against the float chamber body
The fuel level should line up exactly with the little "pip" on the float chamber cover. If it's wrong, you'll need to add (or remove) a washer under the fuel inlet union.
There's a better set of instructions in this thread: https://www.triumphrat.net/classic-vint ... -carb.html
You mentioned you replaced the float valve? It's a good idea to check the float level after doing that...
- Take off the idle jet cover nut
- Push a length of clear pipe over the idle jet
- Hold the pipe against the float chamber body
The fuel level should line up exactly with the little "pip" on the float chamber cover. If it's wrong, you'll need to add (or remove) a washer under the fuel inlet union.
There's a better set of instructions in this thread: https://www.triumphrat.net/classic-vint ... -carb.html
1989 Moto Morini Dart 350
1993 Ducati 750SS
1993 Ducati 750SS
-
- Deceased
- Posts: 598
- Joined: Sun Oct 07, 2018 11:36 pm
- Location: Essex UK
Re: 1957 M16 not running properly
Thanks for that clanger9. That makes sense if it's flooding it or starving it. A manometer! I'll have a try with that soon.
-
- Deceased
- Posts: 598
- Joined: Sun Oct 07, 2018 11:36 pm
- Location: Essex UK
Re: 1957 M16 not running properly
Well, after checking the ignition timing once again-it's 1/2" BTDC fully advanced. Points gap 15 thou.
I have replaced the float needle, and put a better seat in, and still it decides to stick and p petrol everywhere! I checked the float, and when I lift it gently the fuel shuts off as it should. There doesn't appear to be a pimple on the float chamber cover to check the level.
I have decided to leave it for now as it's getting frustrating now. It starts easily but doesn't want to rev and the plug is soaking wet and sooty (not the bear with a wand!).
The main jet is a 105 if I remember correctly.
I need a lie down now!
I have replaced the float needle, and put a better seat in, and still it decides to stick and p petrol everywhere! I checked the float, and when I lift it gently the fuel shuts off as it should. There doesn't appear to be a pimple on the float chamber cover to check the level.
I have decided to leave it for now as it's getting frustrating now. It starts easily but doesn't want to rev and the plug is soaking wet and sooty (not the bear with a wand!).
The main jet is a 105 if I remember correctly.
I need a lie down now!