Front wheel bearings singlesided hub
-
- Member
- Posts: 64
- Joined: Mon Oct 17, 2011 9:34 pm
- Location: Bedfordshire UK
Front wheel bearings singlesided hub
I have to replace the spindle assembly in my wheel due to a damaged bearing cup I have managed to locate a replacement cartridge type, but this is1.5 inch diameter my hub has a shoulder inside reducing it to approx 1.480. I think that I will have to have it reamed to 1.5 does any have any experience of this problem?
- Rob Harknett
- Member
- Posts: 11211
- Joined: Mon Jan 01, 1990 12:00 am
- Location: ESSEX UK
Re: Front wheel bearings singlesided hub
You need to refer to a part by name as seen in your parts list. The wheel has, Cup, bearing oil seal. Which could be replaced for about a fiver, if that is all that is damaged. So wonder why you bothered to source a part intended for a different wheel than you have. Why not look for the correct parts?
-
- Member
- Posts: 64
- Joined: Mon Oct 17, 2011 9:34 pm
- Location: Bedfordshire UK
Re: Front wheel bearings singlesided hub
I haven't bought it yet still trying to get the correct part 012825 by my BMS parts list I was told by club shop yesterday that this is unobtainable and so is the bearing only.Apologies for incorrect terminology it's the bearing race that broke when pressed out.i would be delighted to get the correct part.
-
- Member
- Posts: 851
- Joined: Thu Jan 01, 1998 12:00 am
- Location: ESSEX UK
Re: Front wheel bearings singlesided hub
The Vintage Bearing Co. we're making the complete assembly, I saw these on their stall at Banbury some years ago, price was about £120, so about the same as the sealed bearing which I believe was for full width rear hubs. If you fit the sealed bearing then the spindle will need changing.
- clive
- Member
- Posts: 5669
- Joined: Mon Jan 01, 1990 12:00 am
- Location: LONDON UK
Re: Front wheel bearings singlesided hub
Hang on guys. The question is about the front single sided hub. This is a bearing with front spindle attached. When I fitted one from the club into my 6 inch WD type front hub it just slotted straight in.
clive
if it ain't broke don't fix
if it ain't broke don't fix
-
- Member
- Posts: 1176
- Joined: Wed Oct 12, 2005 10:45 pm
- Location: KENT UK
Re: Front wheel bearings singlesided hub
Was'nt the Andrew engineering one sold for full width hubs and 'some' 1/2 width hubs.That came with the spindle. I dont know the difference between the hub sizes, never needed to look.
- Rob Harknett
- Member
- Posts: 11211
- Joined: Mon Jan 01, 1990 12:00 am
- Location: ESSEX UK
Re: Front wheel bearings singlesided hub
Bearing race, that makes a difference. These parts are not so easy to track down. Also quite expensive. So you do need to make sure what you find is correct before you buy.
-
- Member
- Posts: 746
- Joined: Thu Mar 31, 2005 1:00 am
- Location: BERKS UK
Re: Front wheel bearings singlesided hub
Hi Jim, part no 012825 was still being used in '54 hubs. I have a spare outer race and, while it is not considered pukka practice to interchange taper roller inners and outers, I have done it without any noticeable problems on several occasions. PM me if you want it. Cheers, Andy
-
- Member
- Posts: 64
- Joined: Mon Oct 17, 2011 9:34 pm
- Location: Bedfordshire UK
Re: Front wheel bearings singlesided hub
Hi Andy, that would be great thanks, I would PM you if if I knew how!
- dave16mct
- Member
- Posts: 3245
- Joined: Mon Jan 01, 1990 12:00 am
- Location: LANCASHIRE UK
Re: Front wheel bearings singlesided hub
Hover over 'Andy51' and a drop down 'Private message' show up. Click that and send your message.
Dave
Dave